Jotun Epoxy HR

Name: Jotun Epoxy HR
Brand: Jotun
SKU: ID26176
Price: 318.71 GBP
Availability: InStock

SKU

ID26176

Part A: UN1263 (Class: 3, Pk Grp: III), Part B: UN2735 (Class: 8, Pk Grp: II)

Corrosion protection for surfaces operating at elevated temperatures where long corrosion protection is desired. Suitable for insulated and non insulated surfaces.

Available in 18.8 Litres

From £318.71 £265.59

In stock

Only %1 left

Skip to the end of the images gallery

Skip to the beginning of the images gallery

Product Details

Product Description

Jotun Epoxy HR is a two component polyamine cured phenolic / novolac epoxy coating, formulated as corrosion protection for surfaces operating at elevated temperatures where long corrosion protection is desired. Suitable for insulated and non insulated surfaces.

Best Uses

Designed as a heat-resistant coating, Jotun Epoxy HR is resistant to low temperatures down to -196 °C and high temperatures up to 205 °C continuously. Suitable for use on insulated and non-insulated surfaces. This product may be used as a primer, mid coat or finish coat. Suitable for properly prepared carbon steel, galvanised steel, stainless steel and aluminium substrates. It can be applied on hot substrates up to 150°C. Please refer to the application guide for more detailed information.

Jotun Epoxy HR will offer proper corrosion protection at ambient conditions during construction and shut-down periods. The product passes the standard tests used for qualifying coatings preventing corrosion under insulation (CUI).

Heat resistance

Carbon steel: Continuous: 205°C
Stainless steel: Continuous: 205°C
Alloyed steel (P91): Continuous: 205°C

The continuous operational temperature limits are based on the substrate’s heat-resistant properties.

Application

Preparation

Carbon steel - Sa 2½ (ISO 8501-1)
Stainless steel - Abrasive blast cleaning to achieve a surface profile using non-metallic abrasive media which is suitable to achieve a sharp and angular surface profile
Aluminium - Abrasive blast cleaning to achieve a surface profile using non-metallic abrasive media which is suitable to achieve a sharp and angular surface profile
Galvanised Steel - Sweep blast-cleaning using non-metallic abrasive leaving a clean, rough and even pattern
Shop Primed Steel - Sa 2½ (ISO 8501-1)
Coated surfaces Clean, dry and undamaged compatible coating

Application

Jotun Epoxy HR can be applied by airless spray. Use a brush for stripe coating and small areas. Care must be taken to achieve the specified dry film thickness. Follow Application Guide sheet.

Technical

Technical Details

Approvals and Certifications

Passing CUI 3 multiphase test as described in ISO 19277-2018
Tested in accordance with ISO 12944-9
Tested in accordance with ISO 3248:2000 determination of the effect of heat 500 hours at 204°C on carbon steel
Tested in accordance with ISO 3248:2000 determination of the effect of heat 1000 hours at 204°C on stainless steel (SS304)
Tested in accordance with ISO 3248:2000 determination of the effect of heat 1000 hours at 204°C on alloyed steel (P91)

Technical Info

Components:	Two Pack
Type:	Polyamine cured phenolic / novolac epoxy
Finish:	Matt
Stock Colours:	Aluminium, Light Grey
Tintable:	No.
VOC Content:	362.0g per Litre
Volume Solids:	63%
Suitable Substrates:	Suitable for properly prepared carbon steel, galvanised steel, stainless steel and aluminium substrates
Application Method:	Brush or Airless Spray
Theoretical Coverage:	3.2 - 6.3 m2 per litre
Wet Film Thickness (WFT):	160 - 320 microns
Dry Film Thickness (DFT):	100 - 200 microns
Induction Time:	20 minutes at 23°C
Pot Life:	4 hours at 23°C
Touch Dry:	4 hours at 23°C
Overcoatable:	10 hours minimum at 23°C
Fully Cured:	7 days at 23°C
Cleaner / Thinner:	Jotun Thinner No. 23
Shelf Life:	24 months
Packaging:	Available in 18.8 Litres