Jotun Penguard WF

Name: Jotun Penguard WF
Brand: Jotun
SKU: id17100
Price: 196.31 GBP
Availability: InStock

SKU

id17100

Part A: Non Hazardous, Part B: UN1263 (Class: 3, Pk Grp: III)

A 2 pack water borne epoxy coating for corrosion protection. For short dry to handle and over coating times requirements.

Available in 15 Litres

From £196.31 £163.59

In stock

Only %1 left

Skip to the end of the images gallery

Skip to the beginning of the images gallery

Product Details

Product Description

Jotun Penguard WF is a two component water borne epoxy coating for corrosion protection. Especially designed for new construction where short dry to handle and over coating times are required.

Best Uses

Jotun Penguard WF is formulated to be used as primer, mid coat, finish coat or as single coat system in atmospheric environments. This product is a versatile, fast drying product containing flash rust inhibitors. It cures down to 5°C. Specially designed for new construction where short dry to handle and over coating times are required. Can be used as primer, mid coat, finish coat or as single coat system in atmospheric environments. Suitable for properly prepared carbon steel, aluminium, concrete and galvanised steel substrates. Available with hardener for application at low substrate temperatures.

Suitable for structural steel and piping to be exposed to corrosive environments up to high. Recommended for offshore environments, refineries, power plants, bridges, buildings and mining equipment. Suitable for over coating with water borne acrylics, water borne epoxy and suitable solvent borne coatings.

Application

For Carbon Steel, prepare to Sa2.5. For Aluminium, abrasive blast clean to achieve a surface profile using approved non metallic abrasive media which is suitable to achieve a sharp and angular surface profile. For Galvanised Steel, light brush blast using non metallic abrasive leaving a clean, rough and even pattern. For concrete, allow a minimum 4 weeks curing. Moisture content maximum 5%. Prepare the surface by means of enclosed blast shot or diamond grinding and other appropriate means to abrade the surrounding concrete and to remove laitance.

Apply using airless spray. A brush is recommended for stripe coating and small areas, care must be taken to achieve the specified dry film thickness. Rollers may be used for small areas but is not recommended for first primer coat. However, when using roller application care must be taken to apply sufficient material in order to achieve the specified dry film thickness.

Technical

Technical Details

Approvals

Contributes to satisfying the following credit(s):

Indoor Environmental Quality (IEQ) under LEED® 2009
Environmental Quality (EQ) and Materials and Resources (MR) under LEED® v4

Meets VOC content requirements for BREEAM® International and BREEAM® NOR.
Meets VOC content requirements for Estidama
Meets VOC content requirements for GSAS
Meets requirements for China Environmental Label
Fire test approved for use under Jotun Steelmaster 1200WF

Technical Info

Components:	Two Part
Type:	Water borne epoxy coating
Finish:	Matt
Stock Colours:	Grey XO. Red available on request (MTO 14 day lead time - MOQ 740 litres)
Tintable:	No
VOC Content:	65.0g per Litre
Volume Solids:	51%
Suitable Substrates:	Suitable for properly prepared carbon steel, aluminium, concrete and galvanised steel substrates.
Application Method:	Airless Spray. Brush or Roller for Small Areas or Stripe Coats
Theoretical Coverage:	3.4 - 6.8 m2 per litre
Wet Film Thickness (WFT):	145 - 295 microns
Dry Film Thickness (DFT):	75 - 150 microns
Induction Time:	15 mins at 23°C
Pot Life:	1.5 hours at 23°C
Touch Dry:	1.5 hours at 23°C
Overcoatable:	4.5 hours at 23°C
Fully Cured:	7 days at 23°C
Cleaner / Thinner:	Thinner: Water. Cleaner: Jotun Thinner No. 17 or Jotun Thinner No. 4
Shelf Life:	12 months for Part A, 24 months for Part B
Packaging:	Available in 15 Litres